Metal Stud Framing in Ocala, FL
Metal stud framing in Ocala runs $1.75 to $3.00 per square foot of wall in 2026, layout to top track. Steel studs are the standard for commercial build-outs and a smart pick anywhere walls must stay dead straight, termite-proof, and non-combustible.
Frequently Asked Questions
Metal or wood studs — which is better?
For commercial work, metal is the standard: straight, light, non-combustible, and termite-proof. Wood wins for heavy hanging loads and some residential work. We will tell you which fits your wall.
What gauge do you use?
25-gauge for most non-load-bearing partitions; 20-gauge where doors, cabinets, or code call for more. The plans set the spec on commercial jobs.
Can you hang cabinets or TVs on steel-stud walls?
Yes, with blocking set in the wall during framing. Tell us where the loads land before the board goes on.
Do you frame and hang in one contract?
Usually, yes — one crew from layout to finish keeps the wall true and the schedule simple.
Is the site visit free?
Yes. The visit and the written bid cost nothing.
What Does My Drywall Project Cost?
Drywall is priced by the square foot of wall and ceiling surface — not by the size of your floor. That one fact explains most of the gap between quotes. Here are the ranges we see on real jobs around Ocala, and a calculator built on the same numbers.
Drywall Repair & Patch
Most single repairs land between $250 and $800. Pros price patches by the square foot of damaged area — roughly $55–$75 a foot around Ocala — but every repair carries a minimum job charge, because a patch takes the same setup and the same repeat trips for drying coats whether it's the size of a dinner plate or a door. Grouping several spots into one visit is the cheapest way to fix them: they share one minimum. Some repairs are priced flat by the job instead of the square foot: a wet wall section cut out, dried, and texture-matched (a 4×8 ft section ran $820 flat), long seam cracks (two rooms of ceiling seams re-taped ran $560 flat), and popcorn removal finished smooth (200 sq ft ran $540 flat).
New Drywall Installation
For bare studs finished paint-ready (a standard Level 4 finish), plan on $1.60–$3.05 per sq ft of wall and ceiling surface, materials and labor included. A typical 12×12 bedroom with 8-foot ceilings — that's 528 sq ft of surface — runs about $890–$1,700 around Ocala.
Room Remodel & Replacement
Tearing out old drywall and hauling it off adds $0.60–$1.20 per sq ft on top of new installation — a combined $2.20–$4.25 per sq ft. That same 12×12 bedroom, gutted and re-drywalled, runs about $1,210–$2,330. Opening walls can uncover surprises — water damage, old wiring — and those get priced once they're visible, never guessed at in advance.
Garage Drywall
Garages run $1.55–$3.30 per sq ft depending on finish. Code requires 5/8-inch fire-rated (Type X) board on the wall shared with the house, and on the ceiling when there's living space above it — that's the fire separation, not an upsell. Most two-car garages land between $1,900 and $4,100 finished.
Texture, Skim & Paint
On walls that are already up: skim coating runs $0.95–$1.30 per sq ft, orange-peel or knockdown texture $0.80–$1.85, and primer plus two coats of paint $1.05–$2.80. A typical room's walls — about 415 sq ft of surface — usually land between $770 and $1,930 for texture and paint together.
What Moves the Price
- Finish level. A full Level 5 skim coat (for gloss paint or bright, raking light) costs more than standard paint-ready Level 4.
- Ceilings. Overhead work runs roughly 20–25% more than the same area on a wall — lifts, heavier board, two sets of hands.
- Ceiling height. Taller walls mean longer sheets, scaffolding, and slower work.
- Texture matching. Blending a patch into existing orange peel or knockdown is hand work, and it's priced like it.
- Tear-out. Removing old drywall and disposing of it is its own line on the quote.
- Job size. Small jobs carry a minimum charge; on big jobs the setup spreads over more feet, so the per-foot price drops.
These are planning ranges, not a quote — your final price is confirmed after an in-person look, before any work starts.
A note on materials. These ranges are figured with standard drywall board and the finish level you pick above. Board isn't all the same price, though: moisture- and mold-resistant board — the green or purple board for bathrooms and basements — costs more a sheet than standard board, and on a big job that can push you toward the top of your range, or a little past it. Tell us where the work is and we'll confirm the exact board and the price at the in-person estimate, before any work starts.
Estimate Your Project
Measure the damaged section itself — length × width. A full 4×8 sheet section is 32 sq ft.
Spots done in one visit share a single minimum charge.
Price includes tearing out the old drywall and hauling it off.
Includes 5/8″ Type X fire-rated board on the wall shared with the house — and on the ceiling when there is living space above it — as code requires.
Free — no obligation. Your calculator numbers ride along with the request.
Send Your Project to Ocala Drywall Experts
Your estimate is attached automatically. Add your info and — if you can — a few photos of the project. Photos help us price the job before we ever set foot in the house. Prefer to talk? Call (352) 644-9394.


One job, start to finish
A retail space needed a stockroom wall and an office carved out of open floor. The crew snapped lines at dawn, framed both partitions in steel by the next afternoon, and the board crew started behind them — the store’s opening date held.
- Sample price
- $1.75 to $3.00 per sq ft of wall, framed
- Sample turnaround
- Most interior partitions frame in one to two days.
- Service performed
- Metal Stud Framing
- Final price
- $1.75 to $3.00 per sq ft of wall, framed
- Cost per sq ft
- Per sq ft on hang and finish work. Per job on patch work.
- Turnaround / duration
- Most interior partitions frame in one to two days.
- Payment terms / financing
- Set in the written quote.
Signs that point to this service
- A commercial build-out drawn with steel stud partitions
- Interior walls that must not burn, rot, or feed termites
- Long walls where wood’s bow would print through the finish
Not sure which one you have? Run the symptom check.
What the job covers
- Layout from the plans, chalked and confirmed on the floor
- Light-gauge studs and track, cut and set plumb at spec spacing
- Openings framed for doors, pass-throughs, and glazing per the plans
- Coordination with the trades running wire and pipe through the walls
What it does not cover
- Load-bearing steel design — structural framing comes from the engineer’s drawings, which we build to.
- The drywall itself, unless the hang-and-finish scope is added — it usually is.
- Permits and inspections scheduling, which sit with the GC on commercial work.
Steel framing in Marion County build-outs
Commercial growth along SR-200 and around the medical campuses keeps steel framing in steady demand here, and Florida adds its own reason: termites do not eat steel, and steel does not feed a fire. Residential work uses it too, in garage and storage-room partitions. Framing and board usually travel together — the finished result is on the drywall partition installation page.
Questions on metal stud framing


Need help in Ocala?
Call (352) 644-9394 or send the form. We will tell you plainly what the job needs and what it tends to cost before work starts.
Get a free estimate
Related Services
Commercial Drywall Installation · Commercial Drywall Repair · Drywall Ceiling Repair · Drywall Finishing · Drywall Installation · Drywall Painting and Finishing · Drywall Partition Installation · Drywall Patching · Drywall Repair · Drywall Replacement · Fire-Rated Drywall Installation · Garage Drywall · Moisture and Mold-Resistant Drywall · Popcorn Ceiling Removal · Residential Drywall Installation · Residential Drywall Repair · Soundproof and Acoustic Drywall · Suspended Ceiling Installation · Taping and Mudding · Texture Matching · Water Damage Drywall Repair